TECHNICAL INFORMATION

Power Cable Connection

1Electrical energy to be used as the clipboard and the wellbore along the cable, the cable from the engine merging with the energy of the process must be carried out by competent persons in this regard and certainly very careful. Post the link if solid insulation is done if when you went in the water a short circuit can make the connection area.
Each cable, so the seams won't come off on top of the two cable ends to connect to each other and to be inserted into the ends of a piece of copper pipe can be tightened with a pliers. Air remains in the tire over so that the two layers should be tightly wrapped and then it should be wrapped with PVC tape.
After the defragmentation process is done, the total thickness should not exceed the thickness of the cable is the original cable. If the connection region is made thin enough, the pump can jam when it is lowered into the well.

Engine Water Filling

2With water-cooled submersible motors in stock and the shipping type to avoid freezing antifreeze is used during the waiting period. Water submersible motors before shipment star standard -10°( against freezing water+ they are filled with a mixture of antifreeze.

3

Well before it is lowered into the water in the engine the engine should be checked. I have taken the motor into a horizontal position after removing the plugs and No. 2, less water with pure water the engine must be completed. Clear the air bubbles remaining in the motor to get out again until 30 minutes after filling plugs should be added to distilled water so as to provide sealing and flooding the engine the plug should be turned off.

Use The Cooling Shirt

4The cooling of submersible Motors is provided in the vicinity of the stream with water. Therefore, the water flow around the motor in the submersible pump Assembly to the engine is vital. This flow rate will vary according to the diameter and strength of the motor.
Submersible motor for a long time to be able to serve better the most important factor is to cool the engine. The necessary water for cooling purposes in the vicinity of the motor of the engine speed are given in the following table. Caisson wells in a pool are to be mounted or if the engine or if the wellbore diameter is greater than the diameter of the motor, the motor cooling fluid in the jacket around the fluid in order to provide the router the following speeds must be used.

5

Our company reserves the right to change due to technological developments.

6In this illustration;
Submersible pump
in a vertical format
the water tank
installed.
form.

7In this illustration;
Submersible pumps can work in a horizontal format
demonstrates. The water tank is built into a form.
ATTENTION!
Black line drawn on the side of the engine provide fluidity
that is used to represent the cooling shirt.

8In This Picture ; A Large
Two diver in the well
the pump can work
shows.
Need a lot of water
if required , this
method can be used.

9

In this picture, the submersible pump work in the pool
demonstrates.
Established in the pool in a horizontal manner , submersible pump , correct
pump and can be run with correct installation.

CENTER

Harran University Street 18
SANLIURFA / TURKEY
Telephone:
+90(414) 314 00 35
+90(414) 314 39 49
+90(414) 314 01 18
E-Mail: merkez@yildizsu.com.tr

FACTORY

Organization Industrial Zone 3.Rd. Street 20
SANLIURFA / TURKEY
Telephone:
+90(414) 369 15 15
Fax:
+90(414) 369 15 14
E-Mail: info@yildizsu.com.tr

TECHNICAL SERVICE

Sancaktar Neighborhood
1072. Street
SANLIURFA / TURKEY
Telephone:
+90(542) 645 67 43
E-Mail: servis@yildizsu.com.tr

EXPORT OFFICE

Organization Industrial Zone 3.Rd. Street 20
SANLIURFA / TURKEY
Telephone:
+90(414) 369 15 15
Fax:
+90(414) 369 15 14
E-Mail: export@yildizsu.com.tr

© 2016. All Rights Reserverd. Nur Diver and Electric Motors Limited Company
Design & Hosting Service : AjansEdessa Software and Internet Services